Error code
Samsung washer error code dC
Samsung washer error code dC: A front-load washer will not run with any doubt about the door, and this is that doubt. Every spelling Samsung publishes for it, which machines can raise it, and what to do next.
- From $95 diagnostic, credited to the repair
- 59 cities and neighborhoods covered
- OEM parts available on order
- In writing the price, before anything is opened
What we can confirm
Code dC, from the manufacturer's own documentation
A code is only meaningful together with the machine showing it — the same digits mean different things on different equipment.
The code
dC
A front-load washer will not run with any doubt about the door, and this is that doubt. The usual causes are mechanical and cheap: laundry caught in the seal, a latch that has worn, a striker slightly out of alignment after the machine has walked. Two Samsung specifics are worth knowing. On a FlexWash, a 1dC4 on the upper unit can simply be a missing rubber button beside the latch, and fitting the button is the entire repair. And on some models dC is an unbalanced load rather than a door — Samsung publishes that warning itself.
or call (305) 506-1256
What it narrows down to
The door is not being seen as shut and locked
Diagnostic
From $95, credited to the repair
On the same appliance
What else belongs to the washers
On this make a code belongs to the appliance rather than to a product line. These are the other conditions this machine can display, and the models that can show this one — a display often has more than one thing to say, and the model number decides what any of it costs to put right.
Other codes this appliance can display
Water where it should not be, or a level sensor that cannot agree with itself
Water is not arriving at the rate the machine expects
The cold inlet is being fed hot water
The water is not leaving, or not leaving fast enough
More water in the drum than the cycle called for
The panel thinks a button is being held down
The supply is not what the machine expects
The dispenser drawer is not fully closed
Too much foam, and the machine is waiting for it to collapse
The small add-laundry door is not latched
The drum cannot be spun safely with the load as it sits
The machine is recalibrating its weight sensing, which is normal
The same digits mean different things on different equipment. Search the full code list
In more detail
About Samsung washer error code dC
What dC means on this make
A front-load washer will not run with any doubt about the door, and this is that doubt. The usual causes are mechanical and cheap: laundry caught in the seal, a latch that has worn, a striker slightly out of alignment after the machine has walked. Two Samsung specifics are worth knowing. On a FlexWash, a 1dC4 on the upper unit can simply be a missing rubber button beside the latch, and fitting the button is the entire repair. And on some models dC is an unbalanced load rather than a door — Samsung publishes that warning itself.
The other ways Samsung prints this one
dC · dS · d5 · FL · LO · L0 · dE · dE1 · dE2 · dC1 · dL · 1 dC · 1dC4 · 1dC1
Samsung publishes a condition and then every string that can stand for it, and which one your machine shows depends on the panel it was built with. They mean the same thing and they are one page here, so whichever of them you searched for, this is the right page.
Where this appears, and why not to clear it
On the appliance's own display. Samsung reports errors two ways: machines with a digital display show a code, and the same machines without one blink their cycle lights instead. Both are published by the maker and both are on this site. Photograph what the panel shows before cutting the power — Samsung asks for this itself on its refrigerator and dishwasher pages, and it is the one thing that makes a first visit more useful. A code that has been reset is information a technician no longer has.
What to do about it
- Open the door and run a hand right round the seal, looking for a sock or a corner of something caught in it.
- Close it firmly and listen for the latch. A door that closes without a click is a striker or a latch, not a sensor.
- Look for anything obviously missing or broken around the latch, including on the upper unit of a FlexWash.
- If the door latches properly and the code stays, the switch or the lock assembly is the repair.
Where this goes next
The job this usually becomes is washer door lock repair, and that page carries a starting figure and the reasons that move it. If it turns out to be nothing — and on this make a real share of these are modes, reminders and settings rather than problems — the visit ends there and you pay the diagnostic and nothing else, or call (305) 506-1256 and describe what the panel is doing before booking anything.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards