---
title: "Samsung washer error code dC"
description: "Samsung washer error code dC: A front-load washer will not run with any doubt about the door, and this is that doubt."
url: "https://samsungmiami.support/error-codes/washer-door/"
date_modified: "2026-09-04"
Appliance type: "Washers"
---


# Samsung washer error code dC

### What dC means on this make

A front-load washer will not run with any doubt about the door, and this is that doubt. The usual causes are mechanical and cheap: laundry caught in the seal, a latch that has worn, a striker slightly out of alignment after the machine has walked. Two Samsung specifics are worth knowing. On a FlexWash, a 1dC4 on the upper unit can simply be a missing rubber button beside the latch, and fitting the button is the entire repair. And on some models dC is an unbalanced load rather than a door — Samsung publishes that warning itself.

### The other ways Samsung prints this one

dC · dS · d5 · FL · LO · L0 · dE · dE1 · dE2 · dC1 · dL · 1 dC · 1dC4 · 1dC1

Samsung publishes a condition and then every string that can stand for it, and which one your machine shows depends on the panel it was built with. They mean the same thing and they are one page here, so whichever of them you searched for, this is the right page.

### Where this appears, and why not to clear it

On the appliance’s own display. Samsung reports errors two ways: machines with a digital display show a code, and the same machines without one blink their cycle lights instead. Both are published by the maker and both are on this site. Photograph what the panel shows before cutting the power — Samsung asks for this itself on its refrigerator and dishwasher pages, and it is the one thing that makes a first visit more useful. A code that has been reset is information a technician no longer has.

### What to do about it

- Open the door and run a hand right round the seal, looking for a sock or a corner of something caught in it.
- Close it firmly and listen for the latch. A door that closes without a click is a striker or a latch, not a sensor.
- Look for anything obviously missing or broken around the latch, including on the upper unit of a FlexWash.
- If the door latches properly and the code stays, the switch or the lock assembly is the repair.

### Where this goes next

The job this usually becomes is [washer door lock repair](/services/washer-door-lock-repair/), and that page carries a starting figure and the reasons that move it. If it turns out to be nothing — and on this make a real share of these are modes, reminders and settings rather than problems — the visit ends there and you pay the diagnostic and nothing else, or call [(305) 506-1256](tel:+13055061256) and describe what the panel is doing before booking anything.

What this one means

What dC means on this make

A front-load washer will not run with any doubt about the door, and this is that doubt. The usual causes are mechanical and cheap: laundry caught in the seal, a latch that has worn, a striker slightly out of alignment after the machine has walked. Two Samsung specifics are worth knowing. On a FlexWash, a 1dC4 on the upper unit can simply be a missing rubber button beside the latch, and fitting the button is the entire repair. And on some models dC is an unbalanced load rather than a door — Samsung publishes that warning itself.

The other ways Samsung prints this one

dC · dS · d5 · FL · LO · L0 · dE · dE1 · dE2 · dC1 · dL · 1 dC · 1dC4 · 1dC1

Samsung publishes a condition and then every string that can stand for it, and which one your machine shows depends on the panel it was built with. They mean the same thing and they are one page here, so whichever of them you searched for, this is the right page.

Where this appears, and why not to clear it

On the appliance’s own display. Samsung reports errors two ways: machines with a digital display show a code, and the same machines without one blink their cycle lights instead. Both are published by the maker and both are on this site. Photograph what the panel shows before cutting the power — Samsung asks for this itself on its refrigerator and dishwasher pages, and it is the one thing that makes a first visit more useful. A code that has been reset is information a technician no longer has.

What to do about it

Open the door and run a hand right round the seal, looking for a sock or a corner of something caught in it.

Close it firmly and listen for the latch. A door that closes without a click is a striker or a latch, not a sensor.

Look for anything obviously missing or broken around the latch, including on the upper unit of a FlexWash.

If the door latches properly and the code stays, the switch or the lock assembly is the repair.

Where this goes next

The job this usually becomes is washer door lock repair, and that page carries a starting figure and the reasons that move it. If it turns out to be nothing — and on this make a real share of these are modes, reminders and settings rather than problems — the visit ends there and you pay the diagnostic and nothing else, or call [(305) 506-1256](tel:+13055061256) and describe what the panel is doing before booking anything.

---

**[Read full article: Samsung washer error code dC](https://samsungmiami.support/error-codes/washer-door/)**