--- title: "Resetting a Samsung Ice Maker: Five Cabinets, Five Procedures" description: "How do I reset my Samsung refrigerator ice maker? Resetting a Samsung ice maker: which of the five cabinet layouts you have, why the procedures differ, and…" url: "https://samsungmiami.support/blog/resetting-a-samsung-ice-maker/" date_modified: "2026-09-04" Category: "Troubleshooting" --- # Resetting a Samsung Ice Maker: Five Cabinets, Five Procedures ## How do I reset my Samsung refrigerator ice maker? Why there are five of them Nothing else in this fleet has this shape, and it is worth understanding rather than working around. Samsung does not put its ice makers in one place. Depending on the cabinet, the ice maker lives: - in the **fresh-food compartment**, behind a small panel, fed by a duct of cold air from the freezer;- in the **back of the freezer door**, with its own compartment and its own seal;- in the **bottom** of a bottom-freezer cabinet;- in the **top** of a top-freezer cabinet;- or as a **dedicated assembly** on the cabinets that make both cubed ice and Ice Bites. Those are genuinely different machines. Different fill paths, different sensors, different mechanisms for pushing the ice out, and — because they are different — different reset procedures, which Samsung publishes as five separate articles. The reset button is in a different place on each. The hold time differs. On some the test cycle is initiated by a button behind the bucket; on others by a lever; on others by a sequence on the panel. ## Which one do you have? Open the doors and look before you touch anything. **Ice dispensed through the door, bucket inside the door.** In-door ice maker. It has its own small compartment with a seal against the fresh-food side and, on many cabinets, its own small fan — Samsung's 40E. **Bucket in the fresh-food compartment, usually behind a hinged panel near the top.** The fridge-compartment layout, fed by a duct from the freezer. This is the one most affected by a cabinet packed full, because it depends on air arriving from elsewhere. **Bucket in the freezer drawer or the freezer compartment.** The simplest arrangement, and the one where the fill tube and its heater matter most. **Two kinds of ice.** A second assembly, with its own procedure. Naming that layout is the first genuinely useful thing an owner can do, on this appliance more than any other, and it is the first thing we ask on the phone. ## Two things a reset cannot fix Before you press anything, rule these out, because a reset will not touch either and people spend a week on the wrong thing. **A bucket that is not seated.** If the cabinet cannot see the bucket, it stops making ice entirely — and it says so, with a blinking Ice Off indicator. Take the bucket right out, check nothing is behind it, and push it home until it seats. This is free, it is common, and it usually happens the day after somebody emptied it into a cooler. **A compartment that is not cold enough.** Ice production is driven by temperature. A compartment that has drifted up a few degrees will starve a perfectly good ice maker, and it will not feel warm to a hand. Put a thermometer in it and give it an hour. Around 0°F is what an ice maker needs. Resetting an ice maker in a warm compartment gets you a reset ice maker in a warm compartment. ## What a reset actually does It runs a test cycle. The machine harvests whatever is in the mold, fills, and starts again from a known state. That helps in a specific set of circumstances: when the mechanism has stopped partway through a cycle, when a sensor has latched on a reading that is no longer true, or after the machine has been unplugged and has come back confused. It is genuinely useful for those. It is not a repair, and it does not make anything colder, warmer, cleaner or less frozen. If the mechanism is jammed with ice, a reset will try to harvest into that ice and stop. ## After the reset: wait a day This is where more of these calls go wrong than anywhere else. The compartment has to be at temperature before the machine will make ice at a normal rate, and the first harvest cycles are deliberately slow. A machine that has produced nothing in two hours may be perfectly healthy. Give it twenty-four hours before drawing any conclusion. If there is ice in the bucket the next day, you are done. If there is a little, it is working and catching up. If there is none at all, then you know something. ## When the reset works for exactly a day This pattern comes up often enough to name, and it is not a coincidence: the ice maker resets, produces ice for about a day, and stops again. That is usually the fill tube freezing shut. Samsung wraps a small heater around the tube that feeds the ice maker, precisely to stop that happening, and publishes 33E for it. When the heater stops working, the tube freezes between fills, and clearing or resetting gets you exactly one good cycle before it happens again. It is a much smaller repair than an ice maker and it is worth mentioning on the phone, because the pattern is the diagnosis. ## No codes, and what that means Samsung publishes error codes for refrigerators, dishwashers, washers, dryers, ranges, ovens and microwaves. For ice makers it publishes none at all. The related codes that exist — 8E and 14E for the sensors, 33E for the fill tube heater, 39E for the mechanism, 40E for the ice room fan — are on the refrigerator table, because that is the appliance they belong to. If your cabinet has shown any of them, read them to us: on an appliance with no table of its own, a code from the cabinet it lives in is the closest thing to a direct answer available. Everything else is read from behavior, which is why the five layouts matter, why the pattern of when it stops matters, and why we ask more questions on the phone about this appliance than about any other on this make. --- **[Read full article: Resetting a Samsung Ice Maker: Five Cabinets, Five Procedures](https://samsungmiami.support/blog/resetting-a-samsung-ice-maker/)**